快捷搜索:   服务器  PHP  安全  IIS  linux 安全

OpenVZ 平台VPS Google BBR 加速 TCP 之 Rinetd 方式

OPENVZ实现BBR加速的方式,之前都是使用LKL(详见:https://www.bnxb.com/linuxserver/27274.html),而Rinetd 这种方式其实两三个月前就已经有了,直接将 BBR 内置到了 Rinetd 里边,比较方便的就能配置出来。
以下是手动搭建的方法,非常简单

目前仅支持 64 位系统。

1.下载文件到 /usr/bin/rinetd-bbr

    

#wget -O /usr/bin/rinetd-bbr https://github.com/linhua55/lkl_study/releases/download/v1.2/rinetd_bbr_powered



2.设置权限

    

#chmod a+x /usr/bin/rinetd-bbr



3.创建配置文件

    

#vi /etc/rinetd-bbr.conf



输入以下内容

    

# bindadress bindport connectaddress connectport
 
0.0.0.0 443 0.0.0.0 443



其中的 443 请改为你的端口

IP 地址统一写 0.0.0.0

4.获取接口名称
    
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: venet0: <BROADCAST,POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
    link/void
    inet 127.0.0.2/32 scope host venet0
    inet 10.10.10.10/32 brd 10.10.10.10 scope global venet0:0

看具有公网 IP 的接口名称(比如我的公网 IP 是 10.10.10.10),上面这种的接口是 venet0:0 而不是 venet0

一般的 OpenVZ 应该都是 venet0:0 接口。

5.启动
    

/usr/bin/rinetd-bbr -f -c /etc/rinetd-bbr.conf raw venet0:0 &



注意:将最后的接口改为你上面获取到的接口。在命令最后面加 & 以使其能后台运行。
验证

正常情况下的输出:
    
[    0.000000] Linux version 4.10.0+ ([email protected]) (gcc version 4.9.4 (Ubuntu 4.9.4-2ubuntu1~14.04.1) ) #1 Mon Jul 31 04:50:50 UTC 2017
[    0.000000] bootmem address range: 0x7f2acc000000 - 0x7f2acffff000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16159
[    0.000000] Kernel command line:  [email protected]:1
[    0.000000] PID hash table entries: 256 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory available: 64492k/0k RAM
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:4096
[    0.000000] lkl: irqs initialized
[    0.000000] clocksource: lkl: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.000001] lkl: time and timers initialized (irq2)
[    0.000003] pid_max: default: 4096 minimum: 301
[    0.000021] Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.000023] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes)
[    0.009053] console [lkl_console0] enabled
[    0.009056] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.009128] NET: Registered protocol family 16
[    0.009265] clocksource: Switched to clocksource lkl
[    0.009324] NET: Registered protocol family 2
[    0.009418] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.009421] TCP bind hash table entries: 512 (order: 0, 4096 bytes)
[    0.009503] TCP: Hash tables configured (established 512 bind 512)
[    0.009971] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.009976] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.010060] virtio-mmio: Registering device virtio-mmio.0 at 0x1000000-0x100010b, IRQ 1.
[    0.010186] workingset: timestamp_bits=62 max_order=14 bucket_order=0
[    0.010203] virtio-mmio virtio-mmio.0: Failed to enable 64-bit or 32-bit DMA.  Trying to continue, but this might not work.
[    0.010350] NET: Registered protocol family 10
[    0.010849] Segment Routing with IPv6
[    0.010859] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    0.010993] Warning: unable to open an initial console.
[    0.011006] This architecture does not have kernel memory protection.
[    2.169284] random: fast init done

查看 iptables 规则:
    
# iptables -t raw -nL
Chain PREROUTING (policy ACCEPT)
target     prot opt source               destination
ACCEPT     tcp  --  0.0.0.0/0            0.0.0.0/0            tcp dpt:443 /* LKL_RAW */
DROP       tcp  --  0.0.0.0/0            0.0.0.0/0            tcp dpt:443 /* LKL_RAW */
 
Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination

已经有两条规则了。

顶(0)
踩(0)

您可能还会对下面的文章感兴趣:

最新评论